← all drivers

B&C 10NDL88

10" · 8 Ω · 700 W · 96 dB · datasheet ↗

Thiele-Small parameters

Nominal size10"
Impedance8 Ω
Fs61 Hz
Qts0.25
Qes0.26
Qms7.3
Vas18.4 L
Sd320 cm²
Xmax8.1 mm
Re5.1 Ω
Bl20 T·m
Mms53.5 g
Pe700 W
Sensitivity96 dB

Alignment hint

EBP235 · ported
Sealed Vb (Qtc ≈ 0.71)≈ 2.6 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

DriverFs (Hz)QtsVas (L)Xmax (mm)Sens (dB)FitNotesCompare
Faital PRO 10HP102060 -10.24 -0.0116.1 -2.39 +0.996 =close+
18 Sound 10NTLW250061 =0.27 +0.0222 +3.67.6 -0.596.5 +0.5close4 Ω vs 8 Ω: amp load changes · 500 W vs 700 W: lower power handling · Xmax 7.6 mm < 8.1 mm: lower excursion-limited SPL+
Faital PRO 10FH50060 -10.25 =24.2 +5.87.25 -0.8596 =close4 Ω vs 8 Ω: amp load changes · 500 W vs 700 W: lower power handling · Xmax 7.25 mm < 8.1 mm: lower excursion-limited SPL+
B&C 10NW7667 +60.26 +0.0117.6 -0.86.8 -1.396.5 +0.5close400 W vs 700 W: lower power handling · Xmax 6.8 mm < 8.1 mm: lower excursion-limited SPL+
Faital PRO 10FH53060 -10.25 =23.5 +5.17.5 -0.697 +1close500 W vs 700 W: lower power handling · Xmax 7.5 mm < 8.1 mm: lower excursion-limited SPL+
Faital PRO 10FH50060 -10.26 +0.0125.8 +7.47.5 -0.696 =close500 W vs 700 W: lower power handling · Xmax 7.5 mm < 8.1 mm: lower excursion-limited SPL+
Beyma 10MC700Nd63 +20.22 -0.0320 +1.67 -1.197 +1closeXmax 7 mm < 8.1 mm: lower excursion-limited SPL+
B&C 10NW6459 -20.26 +0.0122 +3.66 -2.196 =close300 W vs 700 W: lower power handling · Xmax 6 mm < 8.1 mm: lower excursion-limited SPL+
B&C 10NW7668 +70.29 +0.0418.5 +0.17 -1.196.8 +0.8close16 Ω vs 8 Ω: amp load changes · 400 W vs 700 W: lower power handling · Xmax 7 mm < 8.1 mm: lower excursion-limited SPL+
Faital PRO 10FH52060 -10.29 +0.0423.5 +5.17.25 -0.8597 +1usableXmax 7.25 mm < 8.1 mm: lower excursion-limited SPL+

Compare the closest 3 against the 10NDL88 →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.