B&C 10CLA64
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 74 Hz |
| Qts | 0.42 |
| Qes | 0.45 |
| Qms | 6.8 |
| Vas | 18.5 L |
| Sd | 320 cm² |
| Xmax | 5 mm |
| Re | 5.5 Ω |
| Bl | 14.5 T·m |
| Mms | 36 g |
| Pe | 250 W |
| Sensitivity | 96 dB |
Alignment hint
| EBP | 164 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 10.1 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| P.Audio SN-10MB | 70 -4 | 0.397 -0.02 | 19 +0.5 | 5 = | 95.6 -0.4 | close | + | |
| B&C 10CLA64 | 72 -2 | 0.41 -0.01 | 21 +2.5 | 4.5 -0.5 | 96 = | close | 16 Ω vs 8 Ω: amp load changes · Xmax 4.5 mm < 5 mm: lower excursion-limited SPL | + |
| Faital PRO 10FH500 | 65 -9 | 0.42 = | 19.2 +0.7 | 7.25 +2.25 | 95 -1 | close | 16 Ω vs 8 Ω: amp load changes | + |
| Radian 5210 | 67 -7 | 0.43 +0.01 | 16.7 -1.8 | 4.7 -0.3 | 94.5 -1.5 | close | Xmax 4.7 mm < 5 mm: lower excursion-limited SPL | + |
| Faital PRO 10FH530 | 67 -7 | 0.39 -0.03 | 20.2 +1.7 | 7.45 +2.45 | 96 = | close | 16 Ω vs 8 Ω: amp load changes | + |
| Beyma 10MCS500 | 70 -4 | 0.366 -0.05 | 18.8 +0.3 | 4.4 -0.6 | 95.7 -0.3 | close | Xmax 4.4 mm < 5 mm: lower excursion-limited SPL | + |
| LaVoce WAN102.50-16 | 76 +2 | 0.43 +0.01 | 24.11 +5.61 | 5.5 +0.5 | 97 +1 | close | 16 Ω vs 8 Ω: amp load changes | + |
| B&C 10 CLA 64 | 74 = | 0.422 = | 18.5 = | 3 -2 | 95.2 -0.8 | close | Xmax 3 mm < 5 mm: lower excursion-limited SPL | + |
| 18 Sound 10NTLW2500 | 66 -8 | 0.39 -0.03 | 20.9 +2.4 | 7.6 +2.6 | 96 = | close | 16 Ω vs 8 Ω: amp load changes | + |
| Faital PRO 10FH520 | 65 -9 | 0.41 -0.01 | 22.7 +4.2 | 7 +2 | 96 = | close | 16 Ω vs 8 Ω: amp load changes | + |
Compare the closest 3 against the 10CLA64 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.