B&C 10CL51
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 58 Hz |
| Qts | 0.38 |
| Qes | 0.42 |
| Qms | 3.5 |
| Vas | 36 L |
| Sd | 320 cm² |
| Xmax | 5.5 mm |
| Re | 5.2 Ω |
| Bl | 11.6 T·m |
| Mms | 30.5 g |
| Pe | 150 W |
| Sensitivity | 96 dB |
Alignment hint
| EBP | 138 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 14.6 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Ciare PFXI10.50W | 58 = | 0.374 -0.01 | 38.5 +2.5 | 4.4 -1.1 | 96 = | close | Xmax 4.4 mm < 5.5 mm: lower excursion-limited SPL | + |
| B&C 10 CL 51 v2024 | 58 = | 0.375 -0.01 | 36 = | 3.9 -1.6 | 96.1 +0.1 | close | Xmax 3.9 mm < 5.5 mm: lower excursion-limited SPL | + |
| Faital PRO 10FE400 | 60 +2 | 0.41 +0.03 | 33.6 -2.4 | 5.62 +0.12 | 95 -1 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Faital PRO 10PR330 | 60 +2 | 0.36 -0.02 | 32.9 -3.1 | 7.27 +1.77 | 95 -1 | close | 16 Ω vs 8 Ω: amp load changes | + |
| SB Audience BIANCO-10MW200 | 58 = | 0.336 -0.04 | 39.3 +3.3 | 5.2 -0.3 | 96.2 +0.2 | close | Xmax 5.2 mm < 5.5 mm: lower excursion-limited SPL | + |
| Beyma 10"WRS 300 | 52 -6 | 0.38 = | 42 +6 | 6 +0.5 | 95 -1 | close | + | |
| the box Speaker 10-250/8-A | 56.8 -1.2 | 0.38 = | 33.3 -2.7 | 4 -1.5 | 95.2 -0.8 | close | Xmax 4 mm < 5.5 mm: lower excursion-limited SPL | + |
| Faital PRO 10FE400 | 60 +2 | 0.47 +0.09 | 35.3 -0.7 | 5.42 -0.08 | 96 = | close | Xmax 5.42 mm < 5.5 mm: lower excursion-limited SPL | + |
| Faital PRO 10PR330 | 60 +2 | 0.33 -0.05 | 32.5 -3.5 | 7.37 +1.87 | 96 = | close | + | |
| Sica 10 N 2.5 PL | 57 -1 | 0.36 -0.02 | 40.9 +4.9 | 4.5 -1 | 96.6 +0.6 | close | Xmax 4.5 mm < 5.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 10CL51 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.