Audax PR380T2
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 4 Ω |
| Fs | 52 Hz |
| Qts | 0.522 |
| Qes | 0.61 |
| Qms | 3.62 |
| Vas | 92 L |
| Sd | 892 cm² |
| Xmax | 2.7 mm |
| Re | 3.1 Ω |
| Bl | 13.7 T·m |
| Mms | 113.6 g |
| Pe | 150 W |
| Sensitivity | 99.4 dB |
Alignment hint
| EBP | 85 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 110.2 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Audax PR380T0 vp_g | 56.9 +4.9 | 0.537 +0.02 | 108.5 +16.5 | 2.8 +0.1 | 98.6 -0.8 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Eminence LEGEND CA154 | 51.1 -0.9 | 0.487 -0.04 | 108.2 +16.2 | 4.5 +1.8 | 100.6 +1.2 | close | + | |
| PD PD 156 v2014 | 50.3 -1.7 | 0.469 -0.05 | 93.4 +1.4 | 5.7 +3 | 97.2 -2.2 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Precision Devices PD 156 v2014 | 50.3 -1.7 | 0.469 -0.05 | 93.4 +1.4 | 5.7 +3 | 97.2 -2.2 | close | 8 Ω vs 4 Ω: amp load changes | + |
| RCF LF 15G302 vp baptiste | 56.8 +4.8 | 0.561 +0.04 | 87 -5 | 6 +3.3 | 97.1 -2.3 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Beyma 15CMV2 v2021 | 49 -3 | 0.485 -0.04 | 104 +12 | 4.5 +1.8 | 96.7 -2.7 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Celestion TF1525E 4 Ohms | 49.8 -2.2 | 0.493 -0.03 | 128.2 +36.2 | 3.5 +0.8 | 100.7 +1.3 | usable | + | |
| Beyma 15CM V2 | 49 -3 | 0.49 -0.03 | 104 +12 | 7 +4.3 | 97 -2.4 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| JBL 615H | 55 +3 | 0.603 +0.08 | 112 +20 | 3.7 +1 | 98.1 -1.3 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Celestion TF 1525E | 49.8 -2.2 | 0.493 -0.03 | 128.2 +36.2 | 3.5 +0.8 | 97.6 -1.8 | usable | 8 Ω vs 4 Ω: amp load changes | + |
Compare the closest 3 against the PR380T2 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.