Audax HT240M0
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 28 Hz |
| Qts | 0.373 |
| Qes | 0.47 |
| Qms | 1.81 |
| Vas | 223.1 L |
| Sd | 332.9 cm² |
| Xmax | 4.5 mm |
| Re | 6.3 Ω |
| Bl | 7.3 T·m |
| Mms | 22.5 g |
| Pe | 80 W |
| Sensitivity | 93.2 dB |
Alignment hint
| EBP | 60 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 86 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Audax HT240HM0 | 28 = | 0.373 = | 223 -0.1 | 4.5 = | 93.2 = | close | + | |
| Davis 25GCA10W v2009 | 26 -2 | 0.332 -0.04 | 235 +11.9 | 4 -0.5 | 93 -0.2 | close | Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| Davis 25GCA10W v2011 | 25.7 -2.3 | 0.332 -0.04 | 235 +11.9 | 4 -0.5 | 92.8 -0.4 | close | Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| Audax HT240M0 vp1 | 27.5 -0.5 | 0.404 +0.03 | 172 -51.1 | 4.5 = | 91.7 -1.5 | close | + | |
| Davis 25SCA10WR | 24.6 -3.4 | 0.327 -0.05 | 237.7 +14.6 | 5 +0.5 | 92.2 -1 | close | + | |
| Audax HIF24HSMC-2CA12 v2 | 29 +1 | 0.41 +0.04 | 171.6 -51.5 | 5 +0.5 | 92.5 -0.7 | close | 40 W vs 80 W: lower power handling | + |
| JBL 127H | 25 -3 | 0.433 +0.06 | 237.9 +14.8 | 4.8 +0.3 | 91.9 -1.3 | close | 50 W vs 80 W: lower power handling | + |
| Dynaudio 30W54 | 24 -4 | 0.357 -0.02 | 257 +33.9 | 7 +2.5 | 92.3 -0.9 | usable | + | |
| SEAS 25 F-EW | 26 -2 | 0.354 -0.02 | 175 -48.1 | 4 -0.5 | 92.3 -0.9 | usable | 60 W vs 80 W: lower power handling · Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| SEAS 25F-EW | 26 -2 | 0.354 -0.02 | 175 -48.1 | 4 -0.5 | 92.3 -0.9 | usable | 60 W vs 80 W: lower power handling · Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the HT240M0 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.