Audax HIF24HSMC-4CA12 v2
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 27 Hz |
| Qts | 0.243 |
| Qes | 0.26 |
| Qms | 3.73 |
| Vas | 179.6 L |
| Sd | 301 cm² |
| Xmax | 5 mm |
| Re | 6.8 Ω |
| Bl | 10.4 T·m |
| Mms | 24.6 g |
| Pe | 40 W |
| Sensitivity | 94 dB |
Alignment hint
| EBP | 104 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 24.1 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Focal 10C01 v2 | 29 +2 | 0.239 = | 176.6 -3 | 5.5 +0.5 | 95.4 +1.4 | close | + | |
| Focal 10C01-T | 29 +2 | 0.237 -0.01 | 175.6 -4 | 5.5 +0.5 | 95.4 +1.4 | close | + | |
| Audax HD24S45TSM-C-2CA14 | 27 = | 0.258 +0.02 | 178 -1.6 | 4 -1 | 94 = | close | Xmax 4 mm < 5 mm: lower excursion-limited SPL | + |
| SEAS 25F-EWX | 26 -1 | 0.23 -0.01 | 175 -4.6 | 8 +3 | 92.9 -1.1 | close | + | |
| SEAS 25F-EWX 8 | 26 -1 | 0.226 -0.02 | 175 -4.6 | 4 -1 | 94.5 +0.5 | close | Xmax 4 mm < 5 mm: lower excursion-limited SPL | + |
| Audax MHD24P45TSM2CA14 | 27 = | 0.259 +0.02 | 209.6 +30 | 4 -1 | 94.1 +0.1 | close | Xmax 4 mm < 5 mm: lower excursion-limited SPL | + |
| Tannoy 250/HF/III-L-Z/8/U | 26 -1 | 0.233 -0.01 | 200 +20.4 | 4 -1 | 94.7 +0.7 | close | 30 W vs 40 W: lower power handling · Xmax 4 mm < 5 mm: lower excursion-limited SPL | + |
| SEAS CA26RE4X vp2 | 24.8 -2.2 | 0.273 +0.03 | 178 -1.6 | 7.6 +2.6 | 92.9 -1.1 | close | + | |
| Monacor SPH-255 | 23 -4 | 0.238 -0.01 | 205 +25.4 | 4.5 -0.5 | 93 -1 | close | Xmax 4.5 mm < 5 mm: lower excursion-limited SPL | + |
| Audax PR240M6 v2014 | 25 -2 | 0.26 +0.02 | 207 +27.4 | 4 -1 | 94.1 +0.1 | close | Xmax 4 mm < 5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the HIF24HSMC-4CA12 v2 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.