Alpine 6015CX
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 4 Ω |
| Fs | 36 Hz |
| Qts | 0.33 |
| Qes | 0.34 |
| Qms | 11.2 |
| Vas | 164.2 L |
| Sd | 835 cm² |
| Xmax | 4.1 mm |
| Re | 3.4 Ω |
| Bl | 16.2 T·m |
| Mms | 116.3 g |
| Pe | 200 W |
| Sensitivity | 99.2 dB |
Alignment hint
| EBP | 106 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 45.7 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Sica 15 Fe 3 CP | 40.2 +4.2 | 0.33 = | 170.4 +6.2 | 5.5 +1.4 | 99.4 +0.2 | close | 8 Ω vs 4 Ω: amp load changes | + |
| JBL 265H-1 | 39 +3 | 0.32 -0.01 | 170 +5.8 | 5 +0.9 | 98.3 -0.9 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Oberton 15NMB35 | 38.93 +2.93 | 0.335 +0.01 | 177.47 +13.27 | 6.75 +2.65 | 99.5 +0.3 | close | 8 Ω vs 4 Ω: amp load changes | + |
| JBL 2265 HPL | 37 +1 | 0.325 -0.01 | 176 +11.8 | 8 +3.9 | 97.9 -1.3 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Oberton 15CX | 38.2 +2.2 | 0.349 +0.02 | 163.8 -0.4 | 6.8 +2.7 | 97.8 -1.4 | close | 8 Ω vs 4 Ω: amp load changes | + |
| B&C 15 PS 40 | 35 -1 | 0.318 -0.01 | 177 +12.8 | 6 +1.9 | 97.4 -1.8 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Conrad CPA15-300 | 36.9 +0.9 | 0.357 +0.03 | 161.6 -2.6 | 5.7 +1.6 | 97.1 -2.1 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 15FH520-4 | 38 +2 | 0.337 +0.01 | 156.6 -7.6 | 7.8 +3.7 | 100.6 +1.4 | close | + | |
| Fane COLOSSUS 15XB v2012 | 38 +2 | 0.322 -0.01 | 168 +3.8 | 7.5 +3.4 | 97.3 -1.9 | close | 8 Ω vs 4 Ω: amp load changes | + |
| DAS Audio 15B v2014 | 39.1 +3.1 | 0.319 -0.01 | 189.5 +25.3 | 4 -0.1 | 98.5 -0.7 | close | 8 Ω vs 4 Ω: amp load changes · Xmax 4 mm < 4.1 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 6015CX →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.