18 Sound 12CX800
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 53 Hz |
| Qts | 0.253 |
| Qes | 0.27 |
| Qms | 4 |
| Vas | 73 L |
| Sd | 530 cm² |
| Xmax | 4.7 mm |
| Re | 5.8 Ω |
| Bl | 18.7 T·m |
| Mms | 48.6 g |
| Pe | 400 W |
| Sensitivity | 99.4 dB |
Alignment hint
| EBP | 196 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 10.7 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| RCF MB 12G301 | 53 = | 0.264 +0.01 | 72 -1 | 4.8 +0.1 | 99.5 +0.1 | close | + | |
| RCF MB 12N301 | 54 +1 | 0.24 -0.01 | 71 -2 | 4.9 +0.2 | 99.7 +0.3 | close | + | |
| Oberton 12B400 | 50.47 -2.53 | 0.249 = | 74.74 +1.74 | 5.25 +0.55 | 98 -1.4 | close | + | |
| B&C 12PLB76 | 50 -3 | 0.23 -0.02 | 75 +2 | 5 +0.3 | 99 -0.4 | close | + | |
| 18 Sound 12ND830 | 55 +2 | 0.28 +0.03 | 72 -1 | 6.5 +1.8 | 99 -0.4 | close | + | |
| Monacor SP-12/300NEO | 53 = | 0.252 = | 68 -5 | 3.5 -1.2 | 99.5 +0.1 | close | 300 W vs 400 W: lower power handling · Xmax 3.5 mm < 4.7 mm: lower excursion-limited SPL | + |
| Monacor SP-12A/300NEO | 53 = | 0.252 = | 68 -5 | 3.5 -1.2 | 99.5 +0.1 | close | 300 W vs 400 W: lower power handling · Xmax 3.5 mm < 4.7 mm: lower excursion-limited SPL | + |
| B&C 12 PLB 76 | 50 -3 | 0.229 -0.02 | 75 +2 | 4.4 -0.3 | 99.7 +0.3 | close | Xmax 4.4 mm < 4.7 mm: lower excursion-limited SPL | + |
| Electro-Voice EVM-DL12X | 56 +3 | 0.24 -0.01 | 77.3 +4.3 | 4.1 -0.6 | 99.2 -0.2 | close | 150 W vs 400 W: lower power handling · Xmax 4.1 mm < 4.7 mm: lower excursion-limited SPL | + |
| B&C 12NDL76 | 50 -3 | 0.27 +0.02 | 69 -4 | 7 +2.3 | 100 +0.6 | close | 16 Ω vs 8 Ω: amp load changes | + |
Compare the closest 3 against the 12CX800 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.